Getting error while installing CUE license. CUE software license install failed. This command will install the necessary software to. Glazenbakje's technical blog. Configure a Cisco Unity Expresse AIM Module in a Cisco Router 2821. Downloading cue-vm-installer-k9.nm-aim.3.1.1.prt1. Can I use AIM-CUE 7.4.1 on CUCME 7.1.x on the Cisco 2651XM. Cue-vm-installer-k9.nm-aim.7.0.6.prt1 Below is the last half of the output. Feb 09, 2008 Glazenbakje's technical blog. Configure a Cisco Unity Expresse AIM Module in a Cisco Router 2821. Downloading cue-vm-installer-k9.nm-aim.3.1.1.prt1.

Reinstalling a Cisco Unity Express Image Using the Boothelper Last Updated: December 10, 2010 This chapter describes the procedures for installing Cisco Unity Express software using the boothelper. Note Use the boothelper method for emergency situations when your system is not responding as required or for a new installation. The helper supports only installations of licenses and full images.

Boothelper mode does not support upgrades or language-only installations. This is a clean installation. It cleans the disk by erasing any existing configuration and voice-mail data before loading the new files on the disk. You must back up your configuration and data files before starting the clean installation, then restore the configuration and data files after the installation takes place.

Both FTP and TFTP servers are required. Note Do not use the boothelper unless you were unsuccessful using the clean install procedure described in. This chapter contains the following sections: • • • • • Prerequisites • Ensure that the TFTP and FTP servers are configured and active. • Ensure that you can ping the Cisco Unity Express module from the TFTP and FTP servers. • See the for a list of supported languages. Task List Installing a software image entails the following sequence of tasks: Table 6 Task List for Reinstalling a Cisco Unity Express Image Using the Boothelper Checklist Checkoff 1. Back up your data and configuration files.

Download the software image files. Enter bootloader configuration parameter values.

Install the software files. Restore the data and configuration files. Downloading the Software Files Downloading the Cisco Unity Express software files is the first software installation task.

Review the prerequisites listed above to ensure that all servers and modules are active and available. SUMMARY STEPS 1. Building Network Management Tools With Tcl/tk Pdf.

Log in and go to the Cisco Unity Express product website at: 2. Click the Download Software link. Download the Cisco Unity Express software files, one zip file and one language package file for each language. Extract the five core files from the zip file. Copy the extracted files and the language package file(s) to the FTP server. Copy the cue-installer.

File to the TFTP server. Copy the other software files to the FTP server. DETAILED STEPS Step 1 Log in and go to the Cisco Unity Express product website at: Step 2 Click the Download Software link.

Step 3 Download the appropriate Cisco Unity Express software files. Zip (application package file) • cue-vm- lang -langpack.

Flipalbum 6 Pro V6.0.3.342 Kor there. Pkg (language package file) The key to the placeholders in the above-mentioned filenames is in.

Hello all, I've tried few times and I'm unable to upgrade from 2.3.3 to 3.0.1 release of Unity Express on AIM module. Hi I have router 2811 with AIM-CUE Card I have to Upgrade this CUE from 3.2 to 7.01 When I try to copy by useing commond Software download clean url ftp://10.10.10.2/cue-vm-k9.nm-aim.7.0.1.pkg give me Downloading ftp cue-vm-k9.nm-aim.7.0.1.pkg Download error Can not download cue-vm-k9.nm-aim.7.0.1.pkg error code 0: error type 'couldn't connect to host' Although I can ping tftp server 10.10.10.2 from cue and vice versa se-192-168-100-10.localdomain ping 10.10.10.2 ------------------------------- tftp server PING 10.10.10.2 (10.10.10.2) 56(84) bytes of data. 64 bytes from 10.10.10.2: icmp_seq=1 ttl=126 time=0.701 ms 64 bytes from 10.10.10.2: icmp_seq=2 ttl=126 time=0.499 ms 64 bytes from 10.10.10.2: icmp_seq=3 ttl=126 time=0.457 ms 64 bytes from 10.10.10.2: icmp_seq=4 ttl=126 time=0.440 ms 64 bytes from 10.10.10.2: icmp_seq=5 ttl=126 time=0.404 ms interface Loopback0 ip address 192.168.100.1 255.255.255.0! Interface Service-Engine0/0 ip unnumbered Loopback0 service-module ip address 192.168.100.10 255.255.255.0 service-module ip default-gateway 192.168.100.1 Is there anything I have to do? Thanks Akaff. I can't find Japan and Taiwan Language package to download for UC560. Se-192-168-80-188# $gpack.uc560.8.6.3.pkg user XXXX password XXXXWARNING:: This command will install the necessary software toWARNING:: complete an add-on install.